B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
0. Introduction
Water treatment process equipment in
commercial swimming pools is the
heart of the technical system and re-
quires special care during the planning
and arrangement of the selected system
components. Special attention is also
required to operate the system success-
fully.
Significant advances in water treatment
technology have been made over the
past five years. Many improvements in
system design and available equipment
have been developed in Europe because
of the stringent regulations on public
swimming pool water quality in Euro-
pean countries. European design stan-
dards and equipment, especially from
Germany, are making their way into the
American market place. These stan-
dards have been developed over many
years as public pools and their use have
changed.
Pools are no longer thought of as simp-
ly swimming pools. They are classified
by function, such as hot whirlpools,
warm water massage pools, therapy
pools, water attraction (leisure) pools,
exercise pools, mineral pools, and of
course swimming pools. Each type of
pool design should consider, water
temperature, bather frequency, water
surface area and specific loading capac-
ity of the chosen water treatment sys-
tem process, as well as other criteria
outlined in this paper.
Water treatment systems have three
main components:
11.. PPooooll HHyyddrraauulliiccss
Distribution of disinfectant and
heated pool water return
Optimal removal of unwanted
particles present in the pool
22.. WWaatteerr TTrreeaattmmeenntt SSyysstteemm
Modern systems contain the following
process:
Flocculation, filtration and auto-
matic water balancing
This provides:
Removal of impurities and un-
wanted particles present in the wa-
ter
Optimum pH-value regulation and
disinfection
33.. DDiissiinnffeeccttiioonn
Modern systems contain one of the
following disinfectants:
Hypochlorous acid (HOCL)
Hypobromous acid (HBrO)
Ozone w/HOCL or HOBr residual
in the pool
These three main components are each
a functioning unit and must be consi-
dered together as a total working sys-
tem.
Incorrect conception and design, im-
proper operation of equipment, impro-
per maintenance or system failure can
cause an unsuitable pool water quality
and allow a possibly unhygienic situa-
tion to develop.
Optimization or economical renovation
of water treatment systems is usually
performed after identifying one or more
of the following:
1. Poorly functioning or defective
system components.
2. Poor pool water quality.
3. High operating costs.
Improving these conditions is the goal
for either optimization or economic
renovation of the system, and should be
kept in mind while reading this paper.
This paper looks at current American
and International pool water quality
standards and the important considera-
tions for proper planning,
design and operation of the individual
system components, as well as the
function of the entire system. It identi-
fies important functions of public
swimming pool water treatment sys-
tems and is intended to assist individu-
als responsible for the safety and opera-
tion of public swimming pools.
Additional information concerning
public swimming pool design can be
obtained from B2E Consulting Engi-
neers, PC, Leesburg, VA. An "Availa-
ble Publications" list is also available.
1. Considerations for the Design and Renovation of New andExisting
Pool Water Treatment Systems
Improper function of individual com-
ponents or of the entire system can lead
to unsatisfactory hygienic conditions in
the pool and increases the personnel
expenses for service, care and repair.
Frequently, the unsatisfactory purifying
effect of such systems are compensated
for by higher introduction of chemicals
and fresh water. This diminishes bather
comfort and increases operating costs.
1.1 Water Circulation Capacity
Calculation and sizing of water treat-
ment equipment requires knowledge of
the available valid local, national and
sometimes international standards.
Local standards, such as adopted by
state regulating agencies, are usually
helpful, but do not offer practical in-
formation concerning the performance
of a given water treatment process.
National standards, such as provided by
the National Spa and Pool Institute
(NSPI), which is approved by the
American National Standards Institute,
Inc. (ANSI), are voluntary standards
based on consensus agreement. This
means that use of this standard by regu-
lating agencies is voluntary and in the
judgment of the ANSI Board of Stan-
dard Review, substantial agreement has
116 N Edwards Ferry Road, NE, Leesburg, VA 20176
Bruce E. Beddow, P.E.
Harald Kannewischer, dipl. Ing.
B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
been made by directly and materially
affected interests (or organizations).
Some international standards, such as
the German, Deutsches Institut fuer
Normen (DIN) 19643 Treatment and
Disinfection of Water for Bathing Wa-
ter, and the Swiss, Schweizerischer
Ingenieur und Architekten-Verein
(SIA) 385/1 Requirements on Water
and on Water Treatment Systems in
Community Pools, are national laws
effective throughout the entire country,
and they are enforced. They clearly
define acceptable water treatment
processes, and accept substitutions to
these standards only after the system
has been put into operation, is tested
and meets the conditions of the stan-
dard. When a system is inadequately
designed or falls out of compliance the
pool is shut down.
The German DIN Standards are recog-
nized around the world as one of the
most comprehensive international stan-
dards and are available in English.
Although they are one of the best, the
requirements can be more difficult to
meet.
For example, the American NSPI Stan-
dard for whirlpools states that the water
circulation rate should be sufficient to
circulate the entire spa water capacity
at a minimum of once every thirty mi-
nutes. Since a typical system connected
to two six person whirlpools contains
roughly 15 m3 (4,000 gal) of water, the
required water circulation rate is 30
m3/h (130 gpm). The German DIN
Standard bases the water circulation
rate on bather load and the frequency of
bathing. Working through the calcula-
tions yields a circulation rate of 108
m3/h (475 gpm) and 90 m3/h (400 gpm)
when ozone is used. This shows a sig-
nificant difference in required water
circulation between the two standards.
This subject will be discussed in more
detail in subsequent sections of this
paper.
When designing to either the American
or German standard the following con-
siderations should be made when plan-
ning or evaluating special use pools:
CChhiillddrreenn’’ss'' ssppllaasshh ppoooollss::
If these water playing areas are fur-
nished with a variety of special splash
equipment, then a higher filter capacity
is required, and should be sized in ac-
cordance with the number of bathers
and the higher frequency of bathing.
Otherwise these pools will maintain a
lower hygienic quality.
HHeeaatteedd ppoooollss aanndd mmaassssaaggee ppoooollss::
These pools typically have smaller
water surfaces and are frequently over-
loaded at public facilities. Considera-
tion of the necessary water surface area
for the expected number of bathers is
absolutely necessary. This will reduce
the possibility for building an under-
sized pool at an unusually high cost.
WWaatteerr SSlliiddeess::
These attractions require a properly
sized treated water circulation rate
calculated in accordance with the fre-
quency of use. For example, 80 people
enter the slide circuit 10 times per hour
for a total of 800 runs per hour. This
would require a treatment capacity of
160 m3/h (700 gpm) or 0.2 m3/h run
(0.9 gpm/run).
HHoott WWhhiirrllppoooollss::
These pools require special attention
and are the subject of a separate paper
by the same author and available
through B2E Consulting Engineers,
P.C., Leesburg, VA.
The performance of the pool
water treatment system is not
constant because the water
flow is not constant over
time. The flow rate reaches a
maximum value immediately
after the backwash cycle,
and then falls off slowly
until the filter resistance
climbs to its maximum value
before the next backwash
cycle.
After the backwash cycle the filter
resistance across the sand filter
amounts to roughly 0.1 bar (1.5 psi)
and climbs until the next backwash
cycle approximately 0.5 bar (7.3 psi).
The filter should be equipped with
pressure measurement gauges, and each
pool system should have a suitable
water flow meter. Good flow measure-
ment devices are:
Inductive process (expensive,
precise, reliable)
Flow meter (rotometer)
Pitot manometer
Paddle wheel flow sensor
An inspection of the total system per-
formance is also possible by establish-
ing the pressure difference across the
main circulation pumps using the ap-
propriate manufacturer's pumping per-
formance curve.
It is possible that during operation the
water flow can drop-off. The cause can
be one or more of the following:
Corrosion in the prefilter causing
restricted flow
Packing of the filter bed
Corrosion of the pump impeller or
housing
Calcium build-up in the heat ex-
changers
Build-up of dirt, scale, etc.
When evaluating a system the meas-
ured water circulation flow rate should
be obtained. According to the sizing
requirements the proper circulation
capacity is measured immediately be-
fore the backwash cycle, and this min-
imum flow rate should also be provided
when a filter is clogged. After the
backwash cycle a higher water flow
rate will be pumped to the pool water
distribution system. (See Figure 1)
1.2 Pool Water Overflow and Return
Even the best treatment systems are
ineffective if the treated pool water
return is inadequately distributed
throughout the entire pool volume. An
exact water distribution provides even
mixing of disinfectant within 5 to 8
minutes. Fast mixing of the total water
volume and efficient removal of sur-
face debris and impurities are important
considerations for optimal system oper-
ation.
B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
Pool water overflow should be hydros-
tatically balanced using a pool over-
flow rim/gutter. Pool rims/gutters of
various architectural designs are an
important component of the hydraulic
system, and should be engineered. This
ensures that the pool water displace-
ment and overflow will be channeled to
the balance tank. (See Figure 2)
1.3 Prefilter/Fiber Screen
A mesh fiber screen is required to catch
large particles before the circulating
pumps. A prefilter is especially impor-
tant with outdoor pools where large
quantities of foliage and similar impuri-
ties are expected. It is frequently rec-
ommended for outdoor pools to install
a large filter element before the balance
tank. Specially designed pool pumps
should be considered for ease of main-
tenance. (See Figure 3)
Figure 3: Compact pool water circula-
tion pump with built-in suction strainer.
1.4 Flocculation
Flocculation at the sand filter alone is
unreliable, and can be helped using a
flocculating agent, such as aluminum
sulfate, iron (+3) chloride or more re-
cently polyaluminum chloride (AlCl3)
or (PAC). These flocculates
only work between a limited pH range
and require a certain reaction time.
Aluminum sulfate is effective between
the range of pH-6.8 to 7.2. With higher
pH-values the flocculation will be de-
layed and leads to cloudy water in the
pool. Flocculation will not be achieved
with a pH level above 7.4. Today PAC
is predominantly used because it is less
pH sensitive and provides better water
clarity.
Dosage levels are typically from 0.3 to
1.5 g/h per m3/h (6.8 - 9.5 g/h per 100
gpm) of the required water circulation
rate.
It is important that the relationship
between pool water loading and floccu-
late injection is given. Flocculation for
outdoor pools is dependent on both the
weather and the number of bathers. For
example, rainy days usually require 0.3
g/h per m3/h (6.8 g/h per 100 gpm) and
peak days 1.0-1.5 g/h per m3/h (23 - 34
g/h per 100 gpm). This is likewise true
for indoor pools where the number of
visitors is changing from day to day.
The injection point should be chosen
near the pump discharge, so that optim-
al mixing is achieved. The injection
coupling should be fixed in the center
of the flow area of the piping and
should have a nozzle to distribute the
flocculating agent.
1.5 Filter
A pressurized sand filter functions only
as well as the backwash can provide the
proper cleaning effect. Backwash is
usually performed as a function of the
pressure drop across the filter. This
normally occurs every 1 to 5 days. The
filter must be backwashed at least once
per week, even when the pressure
gauges indicate that the filter medium
is not completely filled.
Example of a semi-automatic backwash
program:
1. Drain the filter to the sand level
2. Clean air washing for 5 minutes
3. Mixed water/air washing from 7-
10 minutes
4. Clean water washing from 3-5
minutes
5. Filling the filter vessel
6. First filtrate directed into the sani-
tary sewer (2-3 minutes)
Air washing is an important considera-
tion because it fluidizes the sand bed.
The air lifts the sand and the grains
rotate and move against one another.
This action allows dirt fixed to the
grains of sand to be washed out.
The washing process, lifting the sand
bed and actual fluidization, should be
inspected with open filters. Under these
conditions it is also possible to use a
B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
stick (sounding rod) to determine
whether the sand bed is clogged. With
open filters it is certain that uneven or
unsymmetrical air/water patterns can be
recognized.
Figure 3
1. Casing
2. Impellar
3. Rear Wall
7. Motor
11. Casing Seal
12. Drain Plug
13. Impellar Nut
17. Mechanical Shaft Seal
18. Filter Housing
19. Strainer
20. Cover
21. Blockage Check Point
22. Manometer Connection
23. Casing Seal
24. O-Ring
25. Casing Seal Ring
26. Star Handle
During the filter backwash seven
valves service each filter controlled by
an exact time program. The exact regu-
lation of the projected backwash pro-
gram and regulation of the seven valves
can only be accomplished using an
automatic control system.
(See Figure 4)
It is especially important to be aware
that during the operation adjustments
cannot be made. Because of the low
back pressures during backwash, it is
important to have good throttling of the
valves. The system is then able to oper-
ate with reduced pumping capacity.
With high back pressures during the
air/water backwash there will be little
or no air in the filter, which is undesir-
able.
For this reason backwash without back
pressure is required. This means that
with an open inspection port the back-
wash must operate perfectly. A high
water drain connection is therefore not
permitted.
It is likely that long operating cycles
will allow calcium build-up in the filter
media with hard water or pools with
high pH-values. This can be such a
problem that the media (sand) must be
broken-up with a compressor. Addi-
tional calcification of the filter can
result in water bypass through channels
in the media, and result in insufficient
filtration.
The filter bottom is basically a baffle
(60-70 holes/m2 or 6-7 holes/SF). The
holes or nozzles provide an even flow
of filtrate and backwash water. The
main supply connections and filter
distribution network should be de-
signed to distribute the water and air
evenly. If the internal filter distribution
is designed poorly a portion of the me-
dia will be backwashed with air and
another with water.
1.6 Rim/Gutter Overflow Control
During Pool Deck Cleaning
A redirection of the pool overflow wa-
ter is necessary when cleaning fluid is
not permitted in the filter. Cleaning
fluid introduced into the filter leads to
mud (slime) build-up during the back-
wash cycle. The problem occurs when
cleaning fluid is held in the filter vessel
after the backwash cycle, because the
dissolved dirt will be pumped into the
pool. It is best to generously redirect
the channeled water containing clean-
ing agents automatically to the sanitary
sewer. (See Figure 5)
1.7 Important Chemical Parameters
for Water Treatment
General knowledge of the water analy-
sis of the available drinking water,
available from the local water authori-
ty, is needed for the planning, renova-
tion and operation of pool water treat-
ment systems.
1.7.1 Water Hardness
The three different measures of water
hardness are:
Calcium Hardness (Temporary
Hardness)
Non-calcium Hardness (Other
Metals)
Total Dissolved Sol-
ids (TDS)
TDS is the sum of calcium and
non-calcium hardness.
The calcium hardness is the
most interesting value of water
hardness for swimming pool
applications. Calcium hardness
consists of both carbonate and
bicarbonate ions.
In nature carbonic acid rich
water combines with calcium
carbonate (lime) as shown by
the following reaction:
CaCO3 + H2CO3 Calcium Carbonate Carbonic Acid
Ca(HCO3)2 Calcium Bicarbonate
Calcium or magnesium are practically
insoluble in pure water. The calcium
hardness is therefore dependent upon
the carbonic acid content of water.
The stability of calcium carbonate and
carbonic acid in water is both tempera-
See AlsoWhat is the Red Light on My Whirlpool Refrigerator?: Quick Fix Guide - Fridge FixesPlasma whirl reactor apparatus and methods of usePremium Filter Kit To Suit 5 Stage Reverse Osmosis No MembraneJenn-Air JSD2488DEB Ice Maker Support - Genuine OEMture and pressure dependent.
As water containing carbonic acid is
heated carbon dioxide off-gases and the
Ca(HCO3)2 CO2 + H2O + CaCO3 HEAT
B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
calcium hardness rises, as shown by the
following reaction:
Carbon dioxide also off-gasses when
heating pool water and the pH-value
begins to rise. As a result calcium car-
bonate can precipitate out of solution,
which is evident as the water quickly
becomes turbid. Continuous pH correc-
tion, usually with muraitic acid (diluted
hydrochloric acid) or hydrochloric acid,
is necessary.
In order to reduce the amount of cal-
cium precipitate and to regulate the pH-
value, hydrochloric acid is normally
injected into the pool water return. The
hydrochloric acid, which is a stronger
base than carbonic acid, displaces the
carbonic acid according to the follow-
ing reactions:
The resulting carbonic acid disasso-
ciates into,
and the resulting calcium chloride
(CaCl2) is very soluble in water and
will not precipitate out of solution.
Hard water requires pH regulation with
acid.
Soft water requires special attention to
determine whether to regulate with
calcium bicarbonate (soda ash), phos-
phates or with marble chips.
During chlorination injecting free hy-
drochloric acid in water requires suffi-
cient acid capacity (water hardness),
otherwise the pH-value may fall-off
sharply to values below pH-7.
Sodium hypochlorite can be an appro-
priate choice as the disinfectant in
pools with soft water.
1.7.2 pH-Value
The pH-value is the measure of the
hydrogen ion concentration in water
solutions. It is the negative exponent of
the hydrogen ion concentration as
shown by the following equation:
PH = log [H+] = log (1 / [H + ]) Where,
[H + ] = concentration of hydrogen
ions [moles/liter ]
The pH-value is a significant factor for
proper water quality and influences the
following:
The germ destruction rate (ORP)
The effectiveness of the flocculation
agent
Calcification and corrosion in the
system
Reduction of combined chlorine
The normal pH-range should lie be-
tween pH-6.8 and 7.4. The ideal value
is pH-7.2.
Careful attention of the pH-value is not
only necessary for stabilization of the
water hardness, but also to achieve
optimal effectiveness of chlorine disin-
fectant.
The effectiveness of chlorine as a disin-
fectant in water is strongly dependent
upon the pH-value of the water.
(See Figure 6)
pH-6 With chlorine gas injection,
resulting in 97 % hypochlorous
acid (free chlorine, HOCl) and 3
% hypochlorite ion, which is less
effective.
pH-7 Results in only 78 % hy-
pochlorous acid (HOCl).
pH-8 Results in only 24 % hy
pochlorous acid (HOCl).
Therefore, it can be seen that as the pH-
value climbs, significantly greater
quantities of chlorine are necessary to
maintain proper chlorine residuals in
the pool water.
Ca(HCO3)2 + 2 HCl CaCl2 + 2 H2CO3
or,
CaCO3 + 2 HCl CaCl2 + H2CO3
H2CO3 CO2 + H2O
B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
If the pH-regulation system is not func-
tioning properly high concentrations of
acidic or soft water can be pumped into
the pool. This can result in corrosion
and cause cracking of the pool surface
coat.
In addition, it is important to notice that
acid vapor in the area of chemical in-
jection equipment will cause immediate
corrosion. Therefore, chemical rooms
should be closed and ventilated.
1.7.3 pH-Value Regulation with Car-
bon Dioxide
Private hotel pools and sometimes
thermal pools are well served by carbon
dioxide (CO2) for pH-regulation.
Therefore, the solubility of CO2 in
water must be examined.
Hard water treatment systems with high
circulation rates require higher con-sumption of CO2. Theinjection must
occur in regions of high water pressure.
Good injection points are immediately
before or after the filter. The sizing and
arrangement of the injectors is very
important for an even distribution. The
injection should be continuous and in
small quantities. Carbon dioxide pH-
regulation is very expensive for public
pools. The advantage, however, is that
chlorine concentrations in the pool
water tend not to increase and remain
more stable than with use of hydroch-
loric acid (HCl).
Highly loaded pools with hard water,
for example, hot whirlpools or massage
pools, which are treated with chlorine
gas can maintain pH-values 7 without
the addition of muraitic acid (diluted
hydrochloric acid). This is conditional,
however, on the additional disinfectant
required to maintain the desired resi-
dual hypochlorous acid concentration.
In this case, where pH-value measure-
ments, with for example phyenol red,
indicate falling pH-6.8, the fresh water
intake will be increased or a marble
tower will be built into the design.
The acid consumption in hard water
climbs faster with attractions like wa-
terfalls and slides. This creates an un-
favorable, higher concentration of acid
in the balance tank. In addition, acid
consumption increases through unne-
cessarily high temperatures at the sur-
face of the heat exchanger.
1.7.4 Oxidation Potential
The concentration of reductant (organic
impurities) in the pool water can be
measured as the potassium permanga-
nate (KMnO4) consumption of the wa-
ter tested. Permanganate ion (MnO4-), a
deep purple solution, is used to meas-
ure oxidation of these organic impuri-
ties which maintain a residual concen-
tration in pool water. The permanga-
nate solution is added to the sample and
is reduced. When the sample turns
purple the reductants have been oxi-
dized and the permanganate consump-
tion is measured. The following half
reaction shows the reduction of per-
manganate ion:
MnO4 - (aq) Mn + 2 (aq)
Each bather brings a certain quantity of
impurities into the pool water. This has
been documented as 0.8-1.0g combined
nitrogen compounds, measured as
NH4+, which could be either from urine
or sweat. It has also been shown that
each bather brings approximately 50-70
ml of urine into the pool, and that a
residual concentration of 0.5-1.0 mg/l
(ppm) of urine can be found in pool
water. The German Standard, DIN
19643 quantifies this amount to corres-
pond to a potassium permanganate
consumption of approximately 2-6 g
KMnO4.
The higher value is valid for pools with
higher temperature and increased water
movement, such as in hot whirlpools.
The standard impurity concentration is
formulated in the German, DIN 19643
as:
"The average amount of impurity
brought into the pool by one person
during the length of stay is characte-
B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
rized by the reduction potential as
measured with potassium permanga-
nate consumption in grams of oxygen
per person, where 1 g O2 ( 4 g
KMnO4) is the basis."
The potassium permanganate consump-
tion is measured at the pool water over-
flow rim/gutter and at the pool water
return, basically before and after the
sand filter. The difference in the
KMnO4 consumption required to oxid-
ize the reductant of water before and
after the filter is used to calculate the
specific loading capacity of the water
treatment system, where each water
treatment process has an associated
specific loading capacity. This equation
is shown below:
Ox V= E P (1)
Where,
Ox Difference in the reduction of Mn
VII II from overload and return water [g/m3 (ppm)]
V Treated water volume [m3 ]
E Standard impurity quantity [g]
P Number of bathers
The specific loading capacity (loading
factor), b-value, per person for a specif-
ic water treatment process can be ob-
tained as follows:
b = Ox / E = P / V [1/m3] or per-
sons/m3] (2)
where, the standard impurity quantity
is,
1 g O2 ( 4 g KMnO4)
For example:
An existing pool water treatment sys-
tem has a measured overflow water
KMnO4 consumption value, Ox, ow =
6 g/m3 (ppm) and a return water con-
sumption of, Ox,Rw = 4 g/m3 (ppm).
The loading capacity of the water
treatment system is:
Ox = Ox,Ow - Ox,Rw KMnO4 [g/m3
(ppm)]
E = 4 g KMnO4
b = 2 g/m3 / 4 g b = 0.5 1/m3
This specific loading capacity (loading
factor) will be used in Section 4.0 of
this text to determine the proper water
circulation rate of the water treatment
system.
The b-values for several water treat-
ment processes have been determined
empirically with the following results:
1. b = 0.5 1/m3
flocculation + filtration + chlorination (3-step process).
2. b = 0.6 1/m3 flocculation + filtration + ozonation + ac-
tivated charcoal filtration + chlorination
(5-step process).
3. b = 0.5 1/m3
adsorption to activated charcoal powder + diatomaceous earthfiltration w/ activated
charcoal powder + chlorination.
In addition, it should be pointed out
that the measured potassium perman-
ganate consumption of the pool water
return, Ox, Rw, should not exceed a
value greater than 3 g/m3 above the
fresh water (potable water) supplied by
the local water treatment plant.
1.7.5 Oxidation Reduction Potential
The oxidation reduction potential is the
measurement of the germ killing veloc-
ity of the treated pool return water and
is influenced by the pH-value, the free
chlorine content, the fresh water intake
as well as the concentration of reduc-
tant. The oxidation reduction potential
is therefore a parameter for overall
judgment of the water quality.
Correct values for good water quality
with water treatment systems using
chlorine as the disinfectant, measured
with a mercury chloride (Hg2Cl2) elec-
trode and a pH-range between 6.5-7.5
should be > 700 mV.
The oxidation reduction potential
should not be used to control disinfec-
tant injection, but should be measured
and registered and serves as a confir-
mation of proper pool water quality.
1.7.6 Chlorination
When using chlorine gas it should be
mixed into the pool water return using
an injector located in the injector by-
pass piping, whereby in acidic and
neutral pH-ranges hypochlorous acid is
formed. When the pH-value is too high
hypochlorous acid concentration re-
mains low and hypochlorite ion, which
is significantly less effective as a disin-
fectant, may dominate.
Injection of chlorine in water results in
the disassociation of elemental chlorine
into hydrochloric acid and hypochlor-
ous acid as shown below:
Cl2 + H2O + HCl + HOCl
Cl2 = Chlorine H2O = Water
HCl = Hydrochloric Acid
HOCl = Hypochlorous Acid
or reaction in the presence of calcium
bicarbonate into hypochlorous acid,
calcium chloride and carbon dioxide as
shown below:
2Cl2 + Ca (HCO3)2 2HOCl + CaCl2 + 2 CO2
2Cl2 = Chlorine
Ca (HCO3)2 = Calcium Bicarbonate
2HOCl = Hypochlorous Acid CaCl2 = Calcium Chloride
2 CO2 = Carbon Dioxide
When chlorine gas is used a full va-
cuum pressure regulator and venturi
injector system is recommended. This
ensures, that in the event of a chlorine
gas line break, air will be drawn into
the distribution line preventing chlorine
from escaping. The regulator will au-
tomatically shut-off upon sensing rela-
tive overpressure.
The minimum residual concentration of
active (free) chlorine in pool water for
normal use pools should not fall below
0.3 mg/liter (ppm). This value is sub-
ject to locally adopted codes and regu-
lations.
The germ killing velocity of chlorine as
a disinfectant in water is very good,
much faster than with bromine. The
residual free chlorine concentration in
pool water should be sufficient to kill
99.9% of E. Coli within 30 seconds.
Combined chlorine and the byproducts
of breakpoint chlorination are oxidized
products, and cannot be completely
removed from the pool water. For this
reason a constant supply of fresh water
(fresh water intake) is recommended.
1.7.6.1 Free Chlorine
Hypochlorous acid (HOCl) or “free
chlorine” is a very weak acid and dis-
sociates quickly as pH rises above 6 as
shown below:
HOCl H+ + OCl-
HOCl = Hypochlorous Acid
H+ = Hydrogen Ion
B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
OCl- = Hypochlorite Ion
Hypochlorous acid is a much stronger
oxidant than hypochlorite ion and is the
desired disinfectant in chlorinated
swimming pool water. In order to op-
timize the disinfection effect in pool
water a pH - 7.0 - 7.4 is recommended.
(See Figure 6)
1.7.6.2 Combined Chlorine
Upon introduction of ammonia (NH3)
into the pool water from bather or am-
monia laden make-up (fill) water, or-
ganic amines are formed through the
following reactions:
NH3 + H2O NH4OH NH3 = Ammonia
H2O = Water
NH4OH = Ammonia Hydroxide
NH4OH + HOCl NH4OCl + H2O
NH4OH = Ammonium Hydroxide HOCl = Hypochlorous Acid
NH4OCl = Ammonium Hypochlorite H2O = Water
The ammonium hypochlorite is, as with
most salts, a weak acid and disasso-
ciates into water and monochloramine.
NH4OCl NH2Cl + H2O
NH4OCl = Ammonium Hypochlorite
NH2Cl = Monochloramine H2O = Water
The hypochlorous acid (free chlorine)
reacts with the unwanted monochlor-
amine to create dichloramine.
NH2Cl + HOCl NHCl2 + H2O NH2Cl = Monochloramine
HOCl = Hypochlorous Acid NHCl2 = Dichloramine H2O = Water
In swimming pool applications (pH - 7
to 8) monochloramine (96%) predomi-
nates over dichloramine (4%).
1.7.6.3 Breakpoint Chlorination
When the combined chlorine concen-
tration in the pool water climbs above ~
1.0 mg/liter (ppm) breakpoint chlorina-
tion is required to oxidize or “burn-up”
the combined chlorine in the pool thus
removing the chloramines. Breakpoint
chlorination or “superchlorination” is
performed by chlorinating the pool
water to approximately 10 to 12 times
the normally balanced residual free
chlorine concentration. Destruction of
combined chlorine, monochloramine
and dichloramine, occurs rapidly be-
tween pH - 7 and 8 according to the
following reactions:
2 NH2Cl + HOCl N2 + H2O + 3 HCL
2 NH2Cl = Monochloramine
HOCl = Hypochlorous Acid
N2 = Nitrogen H2O = Water
3 HCL = HydrochloricAcid
or
NH2Cl + NHCl2 N2 + 3 HCl
NH2Cl = Monochloramine
NHCl2 = Dichloramine
N2 = Nitrogen 3 HCl = Hydrochloric Acid
Once breakpoint chlorination is
achieved the free chlorine residual
remains high and a chlorine neutralizer
such as sodium bisulfate must be added
to bring the residual free chlorine con-
centration back to an acceptable level
for bathing. Care must be taken not to
overcompensate during neutralization,
which would reduce the free chlorine
residual below the required safe limits.
If this occurs pool water chlorination
must be accelerated to bring the resi-
dual disinfectant concentration into
compliance before bathers may enter
the pool. (See Figure 7)
17.6.4 Fresh Water Intake
If the fresh water, provided by the local
water authority, is of suitable quality
then a constant supply of fresh water
can be introduced into the pool to dilute
the combined chlorine and byproducts
of breakpoint chlorination. This will
extend the period of time between
which breakpoint chlorination is re-
quired. In addition, it will reduce the
concentration of dissolved salts in the
pool, renewing the water, and make
swimming more comfortable for the
bathers. Providing fresh water helps to
maintain the pool water balance and to
prevent the build-up of unwanted com-
pounds as shown in the table below:
Component
Max. Concentration
Iron (Fe)
Manganese (Mn)
Ammonium (NH4+)
< 0.1 mg/l (ppm)
< 0.05 mg/l (ppm)
< 2.0 mg/l (ppm)
B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
Table 1.7.6.4.1 Enrichment of the
Pool Water in Salts, their Origin and
Potential for Damage
If the fresh water, provided by the local
water authority, is not of suitable quali-
ty, as shown in the table below, then
either one of or a combination of the
following may be necessary:
1. Providing fresh water intake from an
unpolluted on-site well. (Well water
analysis required).
2. Pretreating the fresh water with an
activated charcoal powder/high rate
sand filtration system.
3. Continuously injecting activated
charcoal powder into the pool water
pumped discharge before the high
rate sand filter to continually remove
combined chlorine from the pool.
(See Figure 8).
4. Providing a corona discharge ozona-
tor in either the 5-step, complex
ozone or combi-block process ar-
rangements.
Table 1.7.6.4.2 Requirements of the
Fresh (Fill) Water
1.7.6.5 Halomethanes
Carcinogenic compounds are formed
by the reaction of chlorine and bromine
in swimming pool water. These com-
pounds, halomethanes, are created by
reaction of the disinfectant with bro-
mides and organic impurities brought
into the pool by the pool guests.
The recommended maximum
exposure to halomethanes in pool
water is 10 g/liter (ppb). This
value is taken from the
“Deutsches Institut für Normung
(DIN) 19643 Standard”.
The common halomethanes are
trichloromethane or “chlorform”
(CHCl3), bromodichloromethan
(CHBrCl2), dibromochloromethan
(CHClBr2) and tribromomethane
or “bromoform” (CHBr3).
The following table shows the
potential build-up of chlorine and
bromine containing haloforms in
chlorinated water with varying
concentrations of typical organic
impurities (bromide and organics).
Table1.7.6.5 Halomethane Concen-
trations in Pool Water with 2-3
mg/liter (ppm) residual Cl2
1 Normal bather load with guest showers before enteringpool.
2 Normal bather load without guest
showers before entering pool. 3 Insufficient pool watercircula-
tion rate. (Does not meet DIN
19643 Standard).
Use of bromine instead of chlorine as
the residual disinfectant increases ha-
lomethane concentrations in the pool
water.
1.8 Removal of Impurities Found in Pool Water
The following types of impurities exist
in pool water:
1. Suspended impurities (hard particles
which are floating, such as hair, tex-
tile fibers, dead skin, etc.)
2. Dissolved colloidal impurities (se-
cretions from the throat, nose, ears,
fat from the skin, cosmetics, etc.)
3. Completely dissolved impurities
(sweat and urine)
All of the aforementioned impurities
are brought into the pool over the water
surface. An intensive concentration of
these impurities can be found in the
uppermost 10-20 cm (4-8") of water
depth. This is exactly where the bather
is moving about with the most sensitive
areas of the body, like the nose, ears
and mouth.
In spite of proper treated water distribu-
tion and mixing and a large portion of
the water lead to the overflow
rim/gutter, denser particulate matter
will sink to the bottom. This cannot be
avoided.
Figure 9 shows the general distribution
of impurities and particulate matter in
cross section through a typical pool.
The problem exists and should be rec-
ognized and considered during the
design of the treated water return outlet
system.
The pool water distribution system is
an important component in the water
treatment system. In order to disinfect
the pool evenly and thoroughly either a
vertical or horizontal distribution
should be used. If proper mixing of the
residual disinfectant is not achieved
dead zones can develop reducing pool
water quality and causing an increase in
the disinfectant injection rate and there-
fore an increase in chemical consump-
tion.
Organic
Impurities
l/liter
CHCl3
l/liter
CHBrCl2
l/liter
CHBr2Cl
l/liter
CHBr3
l/liter
Total
l/liter
241
482
1003 2003
0.6
0.8
1.3 1.7
0.1
0.5
1.2 1.6
1.5
3.8
6.3 5.8
2.4
3.5
7.7 5.3
4.6
8.6
16.5 14.4
SALT ORIGIN
Chloride Ion
Corrosion of metal above
~ 150 mg/l (ppm) Cl-
- All chlorine containing
disinfectants
- Iron-III Chloride, Aluminum
Chloride and Aluminum
HydroChloride fluoculant
hydrochloric acid
Sulfate
Corrosion of concrete
above ~ 150 mg/l SO42-
- Aluminum-Sulfate (Floculant)
- Sulfuric acid (pH-Regulation)
- Sodium bisulfate
Nitrate
Health risks from 20 mg/l
(ppm) above the NO3-
content of the freshwater
- Oxidized destruction of urine
and other nitrogen containing
impurities (ie. Ammonium)
Calcium
Cloudy water and scaling,
calcification of the filter
media above ~ 70 mg/l
- Dolomite filter material used for
pH- stabilization
- Leaching of mortar in tiled pools
- Calcium hypochlorite disinfect-
ant
B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
Removal of the aforementioned impuri-
ties is achieved in the following steps:
Mechanical Filtration
Flocculation and filtration
Oxidation
Dilution
1.8.1 Suspended Impurities
These hard, floating particles should be
mechanically filtered on the basis of the
strainer effect, electrostatic effect and
the wedge effect. The mechanical ef-
fects of filtration are only effective for
larger sized particles.
1.8.2 Dissolved Colloidal Particles
These dissolved colloidal impurities are
negatively charged and repel one
another. Flocculation allows these par-
ticles to coalesce by aligning the
charged particles whereby the colloids
tend to ball-up forming larger particles.
This effect increases the average size of
the particles, therefore increasing the
filtration efficiency of the system.
These impurities can be effectively
removed either by flocculation or ad-
sorption on activated charcoal media.
1.8.3 Completely Dissolved Impurities
These completely dissolved organic
impurities are primarily oxidized using
chlorine or ozone. The oxidation
process is incomplete in pool water
which contains especially high concen-
trations of organic matter. A small
portion of these impurities are removed
with direct contact with other flocculat-
ing particles and are held in the filter
media.
These impurities can be effectively
removed after flocculation by activated
charcoal powder.
A portion of these impurities and com-
pounds are only able to be diluted with
fresh water to the proper hygienic con-
centration.
The fresh water intake is dependent
upon the pool guests' frequency of
bathing and on the water treatment
process used.
1.8.4 Special Conditions for Outdoor
Pools
The impurities in outdoor pools are
brought in partly due to the bathers and
partly due to the atmosphere. The pool
guests use the pool, unlike with indoor
pools, without properly cleansing
themselves before entering the water
and usually more frequently. There will
be a large quantity of sun cream, cos-
metics, sweat and other impurities car-
ried into the pool.
Additionally, in the absence of small
walk-thru pools at the entrance to the
pool deck organic impurities from the
sun bathing areas will be carried into
the pool.
Outdoor pools, contrary to indoor
pools, will experience a very different
number of bathers in relation to the
number of fair and foul weather days. It
is almost unavoidable to have an exces-
sive number of bathers on beautiful
days.
The surrounding area and the pool will
also be dirtied from wind and storms.
Special problems frequently arise from
trees planted near the pools.
1.9 Heating
The heat exchanger used to heat the
pool water should be manufactured
from series 316 stainless steel or better
and be easily cleanable. A plate frame
heat exchanger is recommended.
In order to minimize carbonic acid off-
gassing, a low primary hot water tem-
perature should be supplied. The pool
water can be heated using a bypass
configuration with a bypass pump. This
reduces energy consumption as well as
the size of the heat exchanger. With
this arrangement care must be taken not
to heat the pool water above 45 C
(115 F).
For example, sizing for a primary
hot water temperature of 50/35 C
(120/95 F) with a pool water tempera-
ture of 27/32 C (80/90 F).
Lower primary water temperature re-
quires greater heat exchange surface
area, however, reduction of acid con-
sumption required for neutralization
of the pool water leads to an improve-
ment of pool water quality for the bath-
ers.
1.10 Balance Tank
A balance tank is required for holding
pool overflow water due to bather dis-
placement and wave motion as well as
backwash water. This tank requires the
same hygienic conditions as the pool.
That means, the tank should be tiled or
surface coated, have a light and portal
for inspection and have a proper means
of entrance for cleaning.
B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
A regular inspection and cleaning of
the balance tank is necessary.
The entrance to the balance tank,
whether it be manhole or submarine
door, must prevent the escape of vapor
into the technical/filter room to protect
equipment against corrosion.
In addition, a vent is required to the
outside.
The pool water overflow piping run-
ning back to the balance tank should be
provided with an open tee connection
as shown in Figure 10. This helps to
reduce the acid concentration as well as
scale build-up in the balance tank by
allowing CO2 to off-gas by the reaction
of hydrochloric acid with calcium car-
bonate and calcium bicarbonate in the
pool water overflow piping.
1.11 Water Distribution in Hidden
Spaces
Pool water return outlets under me-
chanical floors, submerged pool covers,
etc. are required to eliminate build-up
of debris. It is usual to open the valves
to these outlets during night setback
mode for an hour to wash out these
hidden spaces.
2. Water Treatment System
As mentioned in the introduction to this
paper, the entire water treatment system
is made up of the following compo-
nents:
Pool Hydraulics
Treatment System (with floccula-
tion, filtration, and oxidation)
Disinfection
When designing a pool water treatment
system these three components must be
thought of collectively in order to affect
a well integrated and properly working
system.
2.1 Water Treatment
Modern outdoor pools and lightly
loaded indoor pools are usually well
served by the 3-step water treatment
process: Flocculation-Sand Filtration-
Chlorination. The specific loading ca-
pacity (loading factor) of this process
is, b=0.5 1/m3. (See Figure 11)
Highly loaded indoor pools, warm
pools, hot whirlpools and therapy pools
require the 5-step water treatment
process: Flocculation-Sand Filtration-
ozonation-activated Charcoal Filtra-
tion-Chlorination. The loading factor
for this process is, b=0.6 1/m3. (See
Figure 12)
The 5-step (Incl. Ozone) system may
also be suitable for indoor training and
competition pools in order to maintain
good water quality, because of conti-
nual high loading of the pool water
throughout the day. This system offers
better control and reduces the required
flow of fresh water entering the pool.
Three reliable ozone pool water treat-
ment processes are the 5-step, Complex
Ozone and Combi-Block arrangements.
These systems can be essential in eli-
minating “Hyper-Sensitivity Pneumoni-
tis” a bronchial disorder caused by
breathing aerosols containing endotox-
ins (dead micro-organisms). This con-
dition can occur in indoor swimming
pools when the water temperatures are
greater than 86 F or if the pool has
B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
built-in attractions which agitate the
water.
Committing to one of the water treat-
ment processes is one of the significant
responsibilities of the consulting engi-
neer. The influential factors to consider
are:
Indoor swimming pool
Outdoor swimming pool
Bather frequency
Pool water temperature and use
Potable water quality
Potable water and waste water
cost
Operating costs
Safety related items
First Cost
etc.
2.2 Disinfection
Classic disinfection and oxidation is
achieved using pressurized chlorine
gas. Chlorine gas is usually delivered in
65 kg (150 lb) steel bottles.
The disinfection process may require
chlorine gas or hydrochloric acid deli-
very and storage which should be con-
sidered in the planning and design
phase of any project.
The chlorine gas injection system is
arranged with a bypass flow of pool
water pumped across a low flow, high
pressure pump. The water flows
through a venture injector creating a
vacuum on the connected chlorine gas
distribution piping (flexible hose). The
chlorine is drawn into the venturi and is
mixed with the pool bypass water. The
chlorine gas immediately disassociates
into hypochlorous acid and hypochlo-
rite ion. The relative concentrations are
dependent upon the pH-value of the
water.
In addition, hydrochloric acid is
present, which is usually ideal for water
with average to high carbonate hard-
ness, and serves to maintaining the pH-
value.
5-step systems use ozone for the oxida-
tion process and chlorine as the residual
disinfectant.
Chlorine gas distribution technology
has improved and allows engineers to
design a full vacuum system. This type
of system significantly improves the
level of safety associated with chlorine
gas distribution. These systems also
provide automatic switching from an
empty to a full bottle while the system
is in operation.
The danger of such systems is greatly
reduced, and hangs solely on the chlo-
rine gas bottle and valve itself. The
weak points are the shut-off valve and
the valve seal on the bottle. Of course,
the pressure reducing valve and hous-
ing of the vacuum regulator must be
manufactured to handle the high pres-
sure of full gas bottles.
The following chlorine products can be
used as alternatives to chlorine gas:
Sodium hypochlorite:
Delivered as a liquid
B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
Contains ~ 150-170 g/liter (570-
645 g/gal) active chlorine
Strong alkaline solution, pH-10 to
11.
AAddvvaannttaaggee
Well suited with soft water
Simpler and less dangerous to
handle than Chlorine gas
DDiissaaddvvaannttaaggee
Active chlorine concentration
decays ~ 1 % per day or 3.8 g/gal
day (be aware when storing for
long periods)
Sodium hypochlorite by electrolysis:
Manufactured on site through
electrolytic reaction with sodium
chloride (NaCl, cooking salt) solu-
tion
Resulting solution contains ~ 2-5
g/liter (8-20 g/gal) active chlorine
3-4 kg (6.6-8.8 lb) of sodium chlo-
ride and 5-6 kWh of electricity are
required to manufacture 1 kg (2.2
lb) of sodium hypochlorite
AAddvvaannttaaggee
Only NaCl (cooking salt) is re-
quired which can be easily stored
and handled
Same as with delivered sodium
hypochlorite for soft water appli-
cations
DDiissaaddvvaannttaaggee
Sodium hypochlorite solution
generated by the reaction of chlo-
rine gas and hydroxyl ions in wa-
ter must be stored in a large distri-
bution tank
Problematic with hard water, in-
creased HCl consumption
Chlorine gas detectors and alarm
system required
Chlorine gas by electrolysis with
hydrochloric acid solution:
Manufactured on site through
electrolytic reaction with hydroch-
loric acid (HCl)
Electrolysis products are chlorine
gas and hydrogen
3.3 kg (12.5 gal) of 33 % hydroch-
loric acid and 2-2.5 kWh of elec-
tricity are required to manufacture
1 kg (2.2 lb) of chlorine gas
AAddvvaannttaaggee
Produces the same effect as chlo-
rine gas
Eliminates chlorine gas bottle
storage, safer operation.
Chlorine gas is directly dissolved
into the pool water return.
Hydrochloric acid for both electro-
lysis and pH-neutralization can be
stored in one large acid storage
tank.
DDiissaaddvvaannttaaggee
Chlorine detectors and alarm sys-
tem required.
Bromo-chloro-dimethyl-hydantion
(BCDMH)
Delivered as solid
Contains both bromine and chlo-
rine
Strong acid, pH-4
AAddvvaannttaaggee
Active hypobromous acid concen-
tration remains stable over fluctua-
tions in pH. At pH - 7.2: 96% ac-
tive bromine concentration vs 66%
active chlorine.
Indoor/outdoor pools/spas can be
switched over from bromine to
chlorine for outdoor season.
DDiissaaddvvaannttaaggee
Cost 2 to 3 times higher than with chlorine.
Disinfection slower (slower germ killing velocity) thanchlorine,
therefore required residual con-
centrations twice as high as with
chlorine. Residual HOBr = 2 - 4
ppm.
Bromine cannot be stabilized in outdoor pools/spas against UVde-
gradation.
Bromine pools must be breakpoint chlorinated more often thanwith
chlorine to eliminate algae growth
and organic contaminants.
Halomethane concentration in pool water higher with bromineas
compared to chlorine.
3. Pool Water Distribution and Over
Overflow Rim/Gutter Arrange-
ment
The best water treatment systems are of
little use when the pool water distribu-
tion system functions unsatisfactorily.
A perfect water distribution system will
provide an even distribution of the
treated water within 5-8 minutes. In
addition to proper pool water return
distribution, an even, simultaneous
overflow at the pool surface water is
also necessary. In order to achieve
optimal surface water quality with low-
er impurity concentrations, modern
pools are provided with and balanced
for 100 % pool water overflow at the
overflow rim/gutter.
Existing pools under consideration for
renovation should be provided with 100
% pool water overflow systems when-
ever possible.
Figures 2 and 9 show how the pool
water return distribution and overflow
rim/gutter can be renovated to provide
a better cleaning effect at the pool wa-
ter surface. The pool water return is
delivered through low-lying nozzles
located on the pool walls (horizontal
distribution) with 100 % of the surface
water flowing over the rim/gutter and
into the collection channel. The col-
lected pool water is then channeled
directly back to the balance tank.
Reusing existing floor outlets is also
possible when dye tests indicate ac-
ceptable distribution and mixing.
4. Sizing the Water Treatment
System
The calculation of the water circulation
capacity of a public swimming pool is
of significant importance for good wa-
ter quality.
In the United States the water flow rate
through a pool is based on turnover
rate, which is the number of hours to
circulate the pool water volume one
time. This method does not account for
higher impurity concentrations at the
pool water surface, bather frequency or
the specific loading capacity of the
water treatment process. Two frequent-
ly used public pool water treatment
standards are the National Spa and Pool
Institute (NSPI) and the American Pub-
lic Health Association (APHA) stan-
dards. The required pool water circula-
tion rates are shown below:
B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
NSPI = Turnover of 8 [1 volume/8
hours]
APHA = Turnover of 6 [1 vo-
lume/6 hours]
The German, Swiss and Austrian, as
well as many other northern European
pool water quality standards, incorpo-
rate bather loading and pool water sur-
face area and the water treatment
process into the calculation.
The calculation for sizing the water
circulation rate in accordance with the
German Standard DIN 19643 is as
follows:
V = A x n / a x b [m3/h]
where,
V = water flow rate of the treated water
(pool water return) [m3/h]
A = water surface area of the pool [m2]
a = water surface area per person [m2]
n = specific bather frequency per per-
son [1/h]
b = specific loading capacity per person
[1/m3]
The appropriate values for "n" and "a"
according to the DIN standard are
shown below:
as given previously by equation (1),
then if a water treatment process is
used with b=0.5, each person should
have 2.0 m3 (530 gal) of treated water
volume available in which to bathe. (P
= 1 person).
There are, however, special cases,
which require closer consideration:
Wading/ Children’s attraction pools
Warm massage/attraction pools
Water sides
Thermal/Mineral pools
Hot Whirlpools
5. Improvement of the Water Quality
Even if no complaints about pool water
hygiene are made, improvements can
be made to increase bather comfort.
An improvement of the water treatment
is frequently found when the fresh wa-
ter intake can be reduced. Inadequate
water quality can be the result of prob-
lems with the system due to higher
bather loads than the system is able to
handle. These problems exist, for ex-
ample, when the following has oc-
curred:
Subsequent construction on site
Construction of additional attrac-tions
Increase of the water temperature setpoint.
Pools which are not designed for high bather loads and must beadjusted
later to meet the latest operational re-
quirements. For example, with hot
whirlpools and massage pools or chil-
drens’ areas.
The following parameters indicate
a need for improvement of the
pool water treatment system:
Burning sensation in the eyes
Higher concentration of combined chlorine
Higher portion of the oxidiz-ing chemicals, which is
measured as the potassium
permanganate (KMnO4) con-
sumption, over 3 mg/liter
(ppm)
Urine (NH3) concentration, over 1 mg/liter
(ppm)
Under such conditions a remedy is
to control the total chemical
treatment system and to adjust the
entire water balance. The procedure in
such cases is represented by the follow-
ing check list:
CChheecckk LLiisstt ffoorr tthhee PPrroocceedduurree ffoorrOOppttii--
mmiizziinngg tthhee WWaatteerr TTrreeaattmmeenntt
1. Analysis of the Existing Conditions
Determination of the load
Fresh water consumption
Measured water circulation capac-ity
Necessary circulation capacity
KMnO4 consumption before and after the sand filter
Evaluation of the chemical and bacteriological analysis
2. Causes of Improper Operation
(things to look for)
Proper operation of the pressu-rized sand filter
Swimming filter, change filter media, injection correction,
change activated charcoal
Test the injection
Observe the operation
Analyze the operation procedure
3. Operation Manual for Optimization of the Existing System
Correcting the established defect
Optimization of system operation
Repeated measurements
4. System Completion
System completion: Planning for additional installations
5. Commissioning
Testing for improved water quality with reductions in freshwater
supply
Development of a carefully planned inspection table for de-
tailed analysis of the entire system
It is necessary to consider, after the
detailed analysis of the improvements
to the water treatment system, whether
the water circulation rate should be
increases or whether it is meaningful to
develop a more intensive treatment
process.
The graph shown in Figure 13 shows
and example of this problem. (See fig-
ure 13)
Type of
Pool
Pool Depth
[m]
Specific
Bather
Frequency
n [1/h]
Specific
Loading
Capacity
a [1/m2]
Diver Pool
3.40
( 11.0 ft)
1
4.5
(48 sf)
Swimmer
Pool
> 1.35
(> 4.5 ft)
1
4.5
(48 sf)
Non-
Swimmer
Pool
0.6 to 1.35
(2 to 4.5 ft)
1
2.7
(30 sf)
Wading
Pool
**** V = 2 turnovers/h ****
(Turnover = 0.5)
Since,
b = P/V [1/m3]
B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
The curve shows the concentration of
dirt in the rim/gutter overflow water as
a function of the pool water circulation
rate. The dashed lines represent possi-
ble water conditions in the pool, once
with a lower circulation rate of 33 m3/h
(145 gpm) and once with a higher rate
of 100 m3/h (440 gpm). The dashed
parallel lines represent shifts in water
quality using a more intensive water
treatment process. It is generally true
that greater improvements in water
quality can be achieved by providing
higher pool water circulation rates, than
with the costlier methods associated
with improving the water treatment
process.
The results of this graph can be record-
ed and verified by measuring the con-
centration of oxidant in pool water is
indicated and measured by the con-
sumption of potassium permanganate
(KMnO4) across the water treatment
system.
When the circulation rate is increased
additional filters are usually necessary.
Improvements to the water treatment
system capacity can be achieved by
addition of activated charcoal filters.
The activated charcoal acts as a separa-
tion between oxidation and disinfec-
tion. Where the treatment system can
be arranged for disinfection with chlo-
rine or with the ozone/chlorine process.
A further advantage of the installation
of activated charcoal filters exists by
the reduction of chloroform byproduct.
The Federal Health Office in Berlin,
Germany has studied the use of acti-
vated charcoal powder injection before
the sand filter for use in hot whirlpool
applications with very favorable re-
sults.
Further possibilities for the improve-
ment of water treatment processes exist
by installation of equipment to reduce
the concentration of combined chlorine
either by innovative use of activated
charcoal or by UV-radiation.
EExxaammpplleess ooff IInnssuuffffiicciieenntt WWaatteerrQQuuaalliittyy
The temperature of the wad-ing/children’s attraction poolhas
been raised. Additional attractions
were built, whereby loading at the
filters substantially increased and
is overloading the water treatment
system.
Corrective measures:
Daily backwash
Change Floculant and/or increase injection rate
Increase fresh water intake
Addition or improvement of a foot wash pool
Raise chlorine concentration from 0.3 mg/l (ppm) to 0.5 mg/l(ppm)
(Subject to local code)
6. Optimization of Energy Savings
A frequent goal of most renovation and
improvement projects for water treat-
ment systems is reduction of operating
costs.
6.1 Pool Water Heating
Outdoor pools can be heated with sun
absorbers. The required absorber sur-
face is approximately 50% of the pool
water surface area. If a solar absorber
is not possible, because of limited free
area for construction, then a heat pump
should be recommended. Heating out-
door pools with oil or gas is usually no
longer considered.
Indoor pools can be heated by the heat
of rejection from a dehumidification
heat pump in the ventilation unit, the
waste heat from considering boiler
exhaust gas or by geothermal heat
pump systems.
6.2 Heat Recovery
The heat recovery from the constant
pool water effluent offset by the fresh
water intake can be economically re-
covered in indoor swimming pools.
The efficiency of the heat exchanger
process using a shell and tube or plate
frame heat exchanger is between 85
and 90%. This process uses no addi-
tional electric energy for the heat trans-
fer between the warm effluent and cool
fresh water.
The fresh water can be heated up to
between 2 and 4 F of the pool water
temperature reducing the fresh water
intake heating load considerably.
The plate frame heat exchanger usually
has a simple payback period of 2 years.
In addition a waste water heat recovery
unit, incorporating both recuperative
heat exchange as well as heat pump
technology, can be installed. These
systems are self-cleaning and usually
pay for themselves within 6 years.
6.3 Electrical Energy
During night setback operation main
circulating pumps can be switched-off
saving energy. Therefore, it is recom-
mended to equip each water treatment
system with a minimum of two circu-
lating pumps, whereby reduction of the
water flow rate is possible. Leaving
one of two pumps piped in parallel in
operation provides approximately 70%
of the circulation capacity
while saving 75% of the unoccupied
B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
mode pumping energy. (Applicability
is dependent on the resulting pool water
quality, however, is usually not a prob-
lem).
In indoor swimming pools with long
operating hours the under water light-
ing system can have a significant influ-
ence on the electrical energy and oper-
ating costs. A 25-meter, 8 lane pool
could have a $5,000 per year difference
in operating cost by lighting the pool
during the day. (Electricity cost, lamp
replacement cost and labor costs). It is
always recommended to provide ade-
quate daylighting and reduce the oper-
ating time of the underwater lighting
system.
Adequate lighting during the day is
necessary to improve pool use safety.
6.4 Fresh Water Consumption
The fresh water consumption in a
swimming pool is dependent upon the
number of visitors to the facility. In
indoor swimming pools the entrance
counter sales are the measure of the
number of visitors and can also be used
to adjust the fresh water intake.
In outdoor pools the entrance counter
sales are not as reliable because the
visitors come and go as they please
over the course of the day. A good
value to use is twice the number of
counter sales. The best method for
estimating the number of visitors and
therefore, balancing the fresh water
intake, is by counting them from time
to time throughout the day.
In wading/children’s attraction areas
the fresh water intake should be calcu-
lated using a bather frequency of 2, that
is each child uses the pool twice each
hour. For example, with an average of
25 children in the area during the day a
specific bather frequency of 50 children
per hour is used. Then if the children’s
area is open for 8 hours per day, 400
bathers are used for the fresh water
intake calculations. Accordingly the
minimum recommended fresh water
intake is 400 x 30 l/P = 12 m3/Day =
0.5 m3/h ( 2 gpm).
Normally the fresh water intake for
each pool will be divided during initial
balancing of the system according to
the filter capacity (main pool water
circulation rate). This works because
the water circulation rate for each pool
connected on one filter system has been
sized for the expected loading at that
particular pool.
During operation variations in water
quality between pools on the same filter
(water treatment) system may be de-
tected, and at this time a correction of
the fresh water distribution to be differ-
ent pools is necessary.
6.5 Automatic Control and Regula-tions
Modern public swimming pools are
equipped with direct digital control
(DDC) systems. The house energy
management system (EMS) is usually
capable of controlling and managing
operation schedules for many building
components in addition to the pool
water treatment systems. These com-
ponents, whether mechanical or elec-
trical, are initially balanced and pro-
grammed during system start-up
(commissioning).
It is important to adjust all automatical-
ly controlled equipment for economical
optimization of operation. Water
treatment systems can be adjusted to
minimize electrical energy consump-
tion of electricity driven motors as well
as by limiting backwash schedules
through time valuing by programming
proper operational schedules.
Other water treatment equipment have
integral stand-alone controls and must
be adjusted individually, such as pH-
neutralization and disinfection set-
points. These components can only be
optimized to minimize chemical usage
if accurate log sheets are maintained by
operating personnel which can be used
by engineers and technicians to under-
stand how the systems are being oper-
ated. Log sheets can be obtained by
contacting B2E Consulting Engineers,
Leesburg, VA.
7. Final Remarks
It has been shown that to improve the
water treatment process an examination
of all of the appending components and
their combined effects is necessary.
Experience shows that the following
list recognizes problems which occur in
many installations:
Examples of Common Problems:
Automatic pool water balance regulation system test probewa-
ter removal near the floor or from
main drain piping.
Automatic pool water balance regulation system test probewa-
ter removal position next to a
massage jet.
Automatic pool water balance regulation system test probewa-
ter removed from an unloaded
area of the pool.
Regulation ineffective because the chlorine injection systemca-
pacity is undersized.
Fresh water intake and disinfec-tant injection improperlycalcu-
lated.
Back pressure in the filter back-wash drain which inhibitsan
even backwash across the filter
media.
Undersized backwash fluidiza-tion air compressor which isuna-
ble to generate proper fluidiza-
tion of the filter media.
Filter short-circuiting from clogged and calcified filtermedia
(sand filter).
Increased acid consumption from various causes, such asincreased
evaporation at water attractions
or high heat exchanger surface
temperatures.
Germ growth in the activated charcoal, primarily due to low
chlorination in the backwash wa-
ter.
8. Bibliography
* Beddow, B., 1995. Planning, Construction and Operation of
Whirlpools, Leesburg, VA.
Beddow, B., 1995. Ventilation in Natatoria, Leesburg, VA.
* Deutsches Institut für Normung (DIN 19643), 1993.
Aufbereitung von Schwimmund
Badebeckenwasser. Berlin,
Germany.
Eichelsdorfer, D. Jandik, J., Weil, L. Volume 5, 1981. Bildungund
Vorkommen von organischen
Halogenverbindung im
Schwimmbeckenwasser. Archiv
des Badewesens. Wiesbaden,
Germany.
* Herschman, W., 1980. Aufbereitung von
B2E CONSULTING ENGINEERS, P.C.
© Reproduction is Prohibited, 1995.
Schwimmbadwasser. Krammer-
Verlag. Düsseldorf, Germany.
Kannewischer, B. Volume 1, 1993. Badewasserdes infection
mit Chlorgas und mögliche
Alternativen. Umwelttechnik.
Zürich, Switzerland.
Kannewischer, B., 1988. Optimieruug der
Wasseraufbereitung in
öffentlichen Hallen – und
Freibädern, Umwelttechnik. Aug
Switzerland.
Kannewischer, B., 1979. Badewasseraufbereitung für
öffentliche Bäder. BAG Brunner
Verlag. Zurich, Switzerland.
Kurzmann, A., 1978. Schwimmbeckenwasser
aufbereitung mit oder ohne Ozon.
Beratungsbüro und
Laboratorium für Ozon - und
Wasser - Technologie. Walldorf,
Germany.
McGregor, R., Walenczak, W., Rogers, R., Magnetti, L. Volume
2, 1993. Case Study: Ozone-
Based Water Treatment for High
- Quality Air and Water in a Mu-
nicipal Swimming Center. Pro-
ceedings: Eleventh Ozone World
Congress. San Francisco, CA.
Mood, E.W., 1981. Public Swimming Pools: Recommend-
ed Regulations for Design and
Construction, Operation and
Maintenance. American Public
Health Association. Washington,
D.C.
Pacik, D. Volume 4, 1992. Trihalogenmethanein neues
Problem? Archiv des
Badewesens. Wiesbaden,
Germany.
Pitrak, P.J., Rennell, D.S. Second Edition, 1992. Basic
Pool & Spa Technology. Na-
tional Spa and Pool Institute.
Alexandria, VA.
Primarvesi, C.A., Althaus, M., 1980. Wert Bestimmung für das
“Hydrozon-Kompaktverfahren”
durchgeführt durch das Hygiene-
Institute des Ruhrgebiets,
Gelsenkirchen. Hygiene-Institute.
Gelsenkirchen. Germany.
Roeske, W., 1980. Schwimmbeckenwasser
Anforderungen – Aufbereitung –
Untersrchung; Verlag otto Haase,
Lübeck, Germany.
Saun, C., 1989. Planung von Schwimmbä dern, Bau und
Betricb von privaten und
öffentlichen Hallen – Sowie
Freibäern einschlie Blich
Whirlpools and Medizinische
Bäder, Krammer – Verlag,
Düsseldorf, Germany
Bruce E. Beddow, P.E. Harald Kannewischer, dipl. Ing.Normen (DIN) 19643 Treatment and Disinfection of Water for Bathing Wa-ter, and the Swiss, Schweizerischer Ingenieur und Architekten-Verein - [PDF Document] (2024)
Top Articles
Light Your Way With These Expert-Recommended Flashlights
Expert Tips For Top-Rated Tactical Lights For Your Duty Belt
Drys Pharmacy
Ung Resnet Media
Everything You Need To Know About Unturned Escalation (Escalation Guide)
Broken Steel - MangoBait - Fallout 4 [Archive of Our Own]
MST to EST Converter - Savvy Time
Every Time Zone Converter
2022 Apple Trade P36
Nikki Delventhal Age, Bachelor, Single, Cheerleader, Net Worth, Height, Bikini, Camper, Wiki, Bio & More
Uic Printing Funds
Discover the Magic: Elemental Showtimes You Can't Afford to Miss!
Latest Posts
Destiny 2: The Final Shape's Dread Faction Gives the Scorn a Run for Its Money
Best Tactical Police Flashlights: The Ultimate Guide to Illuminating Darkness - TopTenReviewed
Article information
Author: Fr. Dewey Fisher
Last Updated:
Views: 5986
Rating: 4.1 / 5 (42 voted)
Reviews: 81% of readers found this page helpful
Author information
Name: Fr. Dewey Fisher
Birthday: 1993-03-26
Address: 917 Hyun Views, Rogahnmouth, KY 91013-8827
Phone: +5938540192553
Job: Administration Developer
Hobby: Embroidery, Horseback riding, Juggling, Urban exploration, Skiing, Cycling, Handball
Introduction: My name is Fr. Dewey Fisher, I am a powerful, open, faithful, combative, spotless, faithful, fair person who loves writing and wants to share my knowledge and understanding with you.